Product Center
Home » gas use in cutting machine using water
  • How the Laser Cutting Machine Process Works | SPI Lasers

    C02 laser cutting C02 cutting is achieved using a gas laser. The gas in question is a carbon dioxide mixture which has been electrically stimulated. C02 cutting is most often used on non-metal materials as they have a wavelength of 10.6 micrometres.

  • Browns Gas: The 'Water to Fuel' Demos - Not Taught In …

    When we separate water into its components using electrolysis, we end up with two cylinders of gas - one filled with Oxygen, and one filled with Hydrogen. The Hydrogen cylinder will contain exactly twice as much gas as the Oxygen one.

  • Gas-Cutting: Process, Techniques and Advantages | Welding

    Hydrogen is sometimes used as a fuel gas, especially under water to provide a powerful pre-heating flame. Efficiency of Gas-Cutting: Generally, there is a relationship between the speed of travel of the cutting torch and the smoothness of the cut edge.

  • Gas-Cutting: Process, Techniques and Advantages | …

    Hydrogen is sometimes used as a fuel gas, especially under water to provide a powerful pre-heating flame. Efficiency of Gas-Cutting: Generally, there is a relationship between the speed of travel of the cutting torch and the smoothness of the cut edge.

  • Plasma Cutting With and Without Air: Which Should You …

    Adding water—a liquid—to the hot gas state that is plasma is detrimental to the entire cutting process. There are some machines that have accounted for moisture build-up. These units “ have a release valve that can be activated to purge water buildup, but additional filtration is required to completely remove all remaining moisture in the transport lines.

  • Browns Gas: The 'Water to Fuel' Demos - Not Taught In …

    Using Browns Gas, you can run an engine USING ONLY WATER!!! Yes, this amazing discovery has been around for over 15 years.These amazing properties of the "Water Fuel" could revolutionize the way we use Fuels. This discovery has been so controversial that

  • Metalworking Fluid Management and Best Practices | …

    18/10/2012 · In order for companies to realize the most return out of their machine tools and the increasingly expensive cutting tools they use, they must change their thinking about coolants in general. Metalworking fluids account for around 1 to 2 percent of the total cost of the part being manufactured, but can impact the overall manufacturing costs of the part by as much as 95 percent.

  • Oxyfuel Cutting - Process and Fuel Gases - TWI

    Oxy-fuel cutting is a thermal cutting process that uses oxygen and fuel gas (such as acetylene, propane, MAPP, propylene and natural gas) to cut through materials. The oxyfuel process is the most widely applied industrial thermal cutting process because it can cut thicknesses from 0.5mm to 250mm, the equipment is low cost and can be used manually or mechanised.

  • CODE OF PRACTICE - Labour

    Code of Practice: Safety and Health at Work for Gas Welding and Flame Cutting 1.2 Scope and application 1.2.1 In this COP, gas welding and flame cutting refer to a welding or cutting operation with a flame produced by mixing a fuel gas and an oxidant gas in a

  • HigH pressure water jetting in tHe oil and gas industry

    by using high pressure water jetting. With this system, personnel and work pieces are separated using a mobile safety wall. On one side, the part to be cleaned is fixed onto a movable table, which can be operated by a steering wheel. The water tool is mounted

  • Water jet cutter - Wikipedia

    A water jet cutter, also known as a water jet or waterjet, is an industrial tool capable of cutting a wide variety of materials using an extremely high-pressure jet of water, or a mixture of water and an abrasive substance. The term abrasive jet refers specifically to the use of a mixture of water and abrasive to cut hard materials such as metal, stone or glass, while the terms pure waterjet ...

  • Safety in gas welding, cutting and similar processes

    shut off the oxygen and fuel gas cylinder valves; cool the blowpipe with water if necessary; check the equipment for damage or faults, particularly the nozzle. Flashbacks Flashbacks are commonly caused by a reverse flow of oxygen into the fuel gas

  • Water jet cutter - Wikipedia

    Water jets use approximately 0.5 to 1 US gal (1.9–3.8 l) per minute (depending on the cutting head's orifice size), and the water can be recycled using a closed-loop system. Waste water usually is clean enough to filter and dispose of down a drain.

  • Fast Extreme Water Jet Cutter Machine Working, …

    7/8/2018 · Fast Extreme Water Jet Cutter Machine Working, Modern Technology Waterjet Cutting Compilation

  • Water jet cutting - Function, methods and application …

    3/6/2019 · In pure water jet cutting, only water is used for cutting. The final result is determined by the parameters pump pressure, nozzle distance, nozzle diameter and feed speed. The choice of these parameters determines the energy input directly at the point of action and thus also the quality of the surface and the achieved productivity of the cut.

  • What is Gas Welding? (with pictures)

    For example, one gas may heat higher or lower than another, making it more convenient to use with certain metals. Welding is the act of joining two metals by heating them. A variety of metals can be joined using gas welding techniques, although a skilled torch operator is necessary in order to ensure a …

  • This is how water-jet cutting works - URACA

    Cutting is possible with pure water or with hard powdered material (abrasive) mixed water. Pure water cutting. Water-jet cutting with pure water is mainly suitable for cutting soft materials such as food, foams, papers or plastics. In the food sector, for example, it is used for cutting cheese, fruit or …

  • Cutting Fluid Management: Small Machining Operations

    cooling technology: (1) reduces the environmental cost of the machining process by 200% for. jet cooling with a synthetic coolant and by 21% for dry machining, (2) increases the tool life by. 700% at low-cutting speeds and by 50% at high-cutting speeds, (3) decreases part production.

  • Cutting Fluid Management: Small Machining Operations

    Cutting fluids are used in machine shops to improve the life and function of cutting tools. They are also a key factor in machine shop productivity and production of quality machined parts [1,2,3]. 2.1 CUTTING FLUID SYSTEMS Cutting fluid may be applied to a

  • Cut-off Machine Safety Manual - STIHL USA

    Cut-off Machine Safety Manual English 3 – STIHL cut-off machines are equipped with an anti-vibration ("AV") system designed to reduce the transmission of vibrations created by the machine to the operator's hands. An AV system is recommended for those persons using cut-off machine…